Multiquip MS18E Manuel d'utilisateur télécharger pdf (Page 15)

MQ STOW MS18H/MS18E MIXER — PARTS & OPERATION MANUAL — REV. #4 (08/10/06) — PAGE 15

MS18H/MS18E MIXER — ELECTRIC MOTOR

Electric Motor

For maintenance care and operation of the electric motor, refer

to your electric motor instruction booklet furnished with the motor.

Protect the electric motor from dust as much as possible and

keep ventilating openings clean.

The electric motor used in this mixer is a single-phase 1.5 HP

motor. The input voltage requirement for this motor is either 115

or 230 VAC only.

Electric Motor Connection

A 12 inch electrical cable (Figure 2) with a pigtail at one end is

provided with the electrical motor for hookup to a power source.

Table 1. shows the required NEMA connector for the desired

motor horsepower rating. In addition, Table 2 also shows the

matching NEMA approved connector for the required extension

cord.

ALWAYS

, make certain that the power source required for the

electric motor is

correct

and always use the correct NEMA

configuration plug.

Failure

to supply the correct voltage to the

motor can severely damage the motor.

The motor supplied is wired for 115 VAC grounded operation.

Make certain that the correct size grounded (3-wires) extension

cord is used. See Table 4.

Motors can burn out when the line voltage falls 10% below the

voltage rating of the motor. Failure to use proper voltage will

cause the motor to overheat and actuate the overload switch.

If overload protection should actuate because of improper voltage

or any other malfunction, turn the main switch on the motor to the

"OFF" position and correct the problem, press the reset switch

button, and turn the main switch to the "ON" position.

CAUTION:

■

DO NOT spray water at any time on the

electric motor

■

DO NOT operate electric motor in a

explosive environment.

It is strongly recommended that all

electrical wiring be done by a

licensed

electrician

. Special attention should be

given to the electric switch as well as

the over-and-under voltage protection devices as per regulations

set forth in the local electrical safety code handbook.

Electric Motor Voltage Switch

ALWAYS

make certain the motor switch is "OFF" and the

power cord has been disconnected from the power source.

2. Remove the voltage lock-out bolt

(Figure 3). Change the

position of the

voltage change toggle switch

from 115

VAC to 230 VAC. The mixer is factory wired for 115 VAC

operation.

3. Replace the voltage lock-out bolt.

Important!,

when changing the input voltage to the motor

from 115 to 230 VAC the

plug

on the motor power cord

must also be changed. See Table 3.

NOTE

noitamrofnIgniriWrotoMcirtcelE.3elbaT

rotoM

rewopesroH

gnitaR

esahPelgniS-CAV032-511

rotcennoCgulPAMENAMENgnitaM

rotcennoCelcatpeceR

PH5.1

)CAV511(

735049MEN/PP02-5L835049MEN/PR02-5L

PH5.1

)CAV032(

935049N/PP02-6L045049N/PR02-6L

eziSdroCnoisnetxEdednemmoceR.4elbaT

ledoMrotoMegatloV

.tf05

)m42.51(

.tf57

)m68.22(

.tf001

)m84.03(

.tf002

)m69.06(

E81SM

)cirtcelE(

PH5.1

51121.oN01.oN8.

oN6.oN

03241.oN21.oN21.oN8.oN

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 121 122

Commentaires sur ces manuels

Pas de commentaire

Multiquip MS18E Manuel d'utilisateur Page 15

Commentaires sur ces manuels

Produits connexes et manuels pour Mélangeurs Multiquip MS18E