MULTIQUIP CMS-94S Manuel d'utilisateur télécharger pdf (Page 12)

PAGE 12 —STOW CMS-94S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #2 (08/04/06)

STOW CMS-94S CONCRETE MIXER — GENERAL INFORMATION

Application

This mixer is

only

intended for the production of

concrete

The mixer must be used for its intended purpose and is not

suitable for the mixing of

flammable

explosive

substances. The mixer

must not be used

in an explosive

atmosphere. Use Table 4 (Mixing Hints) as a guide when

mixing concrete for various applications.

Power Plants

The STOW CMS-94S mixer can be powered by either a

Honda GX-240 air-cooled, 4-stroke

gasoline engine or a 1.5

HP electric motor. Refer to Table 2 to for specific engine or

electric motor data information.

Electrical

If mixer is equipped with an

electric motor

, make sure that

the power being supplied to the motor corresponds to the

voltage rating label on the motor. Supplying the wrong voltage

to the electric motor will cause severe electrical damage to

the motor.

Always make sure the

OFF/ON

switch on the electric motor

is in the

OFF

position before applying power.

It is

strongly recommended

when inserting the mixer's

power cord into a receptacle, that a G.F.C.I. (

Ground Fault

Current

Interrupter

) receptacle be used (115 VAC

applications).

Extension Cables

The extension cable should be a 3-wire configuration that

includes a ground wire that conforms to UL code. The wire

cross section must be a minimum of 2.5 mm

. Choose an

extension cord of adequate current carrying capacity as ref-

erenced in Table 5. Remember

cable distance

affects the

current-voltage capacity of the extension cable.

Ensure that the extension cable is carefully laid out avoid-

ing

wet areas

sharp edges

and locations where vehicles

might run over it. Avoid allowing the extension cable to be

trapped underneath the mixer.

Unroll the extension cable fully or it will overheat and could

catch fire. Make sure that all extension cable connections

are dry and safe. Replace any defective or badly worn ex-

tension cable immediately.

Hardware

Check all hardware on the mixer before starting. Periodically

inspect all hardware. Loose hardware can contribute to early

component failure and poor performance. Use Table 3 as general

guideline when the torqueing of mixer hardware is required.

Remember to keep all mixer hardware components tight.

Engine Maintenance

For basic engine maintenance, refer to the engine maintenance

section in this manual. For a more detailed engine maintenance,

refer to the

Honda

Engine Owner's manual furnished with the

engine.

euqroTerawdraH.3elbaT

noitadnemmoceR

erawdraH

retemaiD

)sbl-tf(euqroT

81xhcni-61/541

61xhcni-8/342

42xhcni-8/373

31xhcni-2/193

31xhcni-2/1

)8edarG(

STNIHGNIXIM.4elbaT

SNOITACILPPA

XIM

SOITAR

SEITITNAUQHCTAB

HCTAB.XORPPA

TUPTUO

.sbl211TNEMEC

).sgK05(

gaB

DNASENOTS

.TF.UCRTL.TF.UCRTL.

TF.UCRTL

yranidrOtsoM

4:2:1GAB2/14/1-1532/1-2173 58

snoitadnuoF

6:3:1GAB3/14/1-1532/1-2174/3-287

ssaMhguoR

etercnoC

8:4:1GAB4/14/1-1532/1-2174/3-287

,sroolFthgitretaW

.ctE,stiP,sknaT

3:2/1-1:1GAB3/24/1-1533 173 58

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 81 82

Commentaires sur ces manuels

Pas de commentaire

MULTIQUIP CMS-94S Manuel d'utilisateur Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Jouets et accessoires MULTIQUIP CMS-94S