MULTIQUIP gb43sc Manuel d'utilisateur télécharger pdf (Page 32)

PAGE 32 — GLOBUG 4-SPOT — OPERATION AND PARTS MANUAL — REV. #3 (12/15/08)

GLOBUG 4-SPOT — NAMEPLATE AND DECALS

When the GloBug is used for

non-lighting applications,

un-plug GloBug AC power cord

from the generator.

ALWAYS

CAUTION

DCL402

ALWAYS OFFturn lamp

first, before shutting down

generator.

CAUTION

DCL409

LAMP INFORMATION

Once lamp is turned

t will take about 20 minutes

before lamp can be turned

back on.

OFF,

Allow lamp to cool down

before turning back on.

I

NEVER place the GloBug

wheels in standing water. The

possibility of electrical shock,

even death! Exists.

DANGER

DCL400

ELECTRICAL

SHOCK HAZARD

To avoid injury,

you MUST read

and understand

operator’s manual

before using this

machine.

Ask for training

as needed.

This machine to

be operated by

qualified

personnel only.

P/N35137

WARNING

DCL416

DANGER

When replacing lamp and to prevent electrical

shock, shutdown the generator beforeALWAYS

replacing lamp. Remember to let lamp cool before

removing. Use only recommended type lamp as

listed in parts manual.

ELECTRICAL

SHOCK HAZARD

WARNING

DANGER

WARNING

DCL412

When lifting of the GloBug is

required, attach a rope

or chain to the lift hanger.

use any other lifting points to

lift the GloBug.

ALWAYS

DO NOT

LIFT

HANGER

To prevent tipping, use

in winds that exceed 22 mph

(10 m/sec).

NEVER

DANGER

DCL411

GlowBug

INFORMATION

NEVER use on an incline of 5

degrees or more. The possibility

of tipping exists.

NEVER use in rain or wet

conditions. The possibility of

electrocution exists.

ALWAYS OFFturn generator

before performing maintenance.

ALWAYS apply parking brake

to prevent moving.

When moving is required, lower

mast fully.

W

deploy outriggers to prevent

tipping.

ALWAYShen raising mast,

ALWAYS keep tires inflated

to correct pressure. Low or

incorrect tire pressure could

result in brake malfunction.

DCL407

CAUTION

TIRE PRESSURE

Recommended tire pressure:

35.5 PSI

(225 kPa)

WARNING

DCL414

OUTRIGGER

DEPLOYMENT

Pull outrigger upward at the tip end

and rotate backwards until it locks in

place.

SETTING:

To unlock outrigger, push downward

on the counter-weight lever indicated

by arrow. Grab hold of outrigger, pull

upward, push down and place in stow

position.

RELEASE:

A

C

C

I

R

C

U

I

T

B

R

E

A

K

E

R

A

C

C

IR

C

U

IT

B

R

E

A

KER

1

2

0

/

2

4

0

V

1

2

0

/

2

40V

3

0

A

30

A

1

2

0

V

3

0

A

2

0

A

2

0

A

0

N

O

F

F

I

D

L

E

C

O

N

T

R

O

L

O

P

E

R

A

T

I

O

N

S

W

I

T

C

H

O

N

O

F

F

F

U

L

L

P

O

W

E

R

S

W

I

T

C

H

1

2

0

V

1

2

0

V

/

2

4

0

V

1

2

0

V

O

F

F

O

F

F

2

1

A

2

1A

GA

-6H

6

00

0

OUTRIGGERS

DEPLOYED

STOW

POSITION

DANGER

DCL405

ELECTRICAL

SHOCK HAZARD

To prevent electrical shock or

electrocution, the generator

be connected to an

earth ground.

MUST

(See NEC Article 250)

GROUND

To prevent burns, NEVER

touch lamp while lamp is on.

Lamp surface gets extremely

hot! A LWAYS allow sufficient

time for lamp to cool down

before touching.

DCL417

WARNING

BURN HAZARD

To prevent burns,

ballast or cover while

lamp is on. These surfaces are

extremely hot! allow

sufficient time for both surfaces

to before touching.

NEVER

touch

ALWAYS

cool down

BURN HAZARD

WARNING

DCL415

DANGER

DCL418

HIGH VOLTAGE

BALLAST

BOX

MODEL

SERIAL NO.

DCL401

3

12

13

14

15

16

9

19

18

10

20

17

7

8

6

11

4

5

NEVER touch a live power cord

or active electrical components

with wet hands or while standing

in water. The possibility of electrical

shock or even death! exists.

DANGER

DCL410

ELECTRICAL

SHOCK HAZARD

21

NAMEPLATE AND DECALS

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 53 54

Commentaires sur ces manuels

Pas de commentaire